GENERAL CRUSHER INFORMATION CHAPTER 3 CRUSHER TERMINOLOGY Throughout this instruction manual technical terms are used to describe the crusher its components and its operation These terms are defined herein with the intent of avoiding any confusion or misunderstanding Figure Jaw crusher terminology
Bottom End Torque s; Main Cap Bolts Torque Spec 18 ft lbs 60° 15° Connecting Rod Bolts Torque Spec 18 ft lbs 75° Oil Pump Cover Screws Torque Spec 5 ft lbs Oil Pan Torque Specs 8 ft lbs Oil Pan Drain Plug Torques 18 ft lbs Intake Manifold and Fuel Rail Torque Spec; Intake Manifold 15 ft lbs Fuel Rail Torque Specs 8 ft lbs
Chrysler 300 OHV Cylinder Head Small Bolts Torque Specs 15 ft lbs 25 ft lbs Timing Chain and Camshaft Installation On the Chrysler OHV engine the timing system is ran by the use of a single chain This chain system consists of a sprocket on the single center located camshaft and one sprocket on the engines crankshaft
3 Bolting torque to develop 50% Bolt Yield Stress at Nut Factor K=; This Table is applicable to Never Seize paste and Fel Pro lubricant K= The above Table is applicable only for ASTM A320 Grade B8 Class 2 and A193 Grade
Note All Torque figures given as or Recommended Seating Torque figures except the Socket Set Screw torque given as Proof Torque All values given in Newton meters Nm Figures only valid for coarse thread screws and should be used as a reference guide only as variables such as but not limited to temperature lubrication plating and condition of mating threads will
Chrysler PT Cruiser Main Cap Bolts Torque Specs M11 60 ft lbs Chrysler PT Cruiser Main Cap Bolts Torque Specs M8 22 ft lbs Piston and Connecting Rod Installation To install the pistons and connecting rods you must first install the piston rings into each piston Be careful not to stretch the rings or break them during
Detailed torque specifications for the Dodge Ram 4 made from 2009 2019 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs
TORQUE TENSION REFERENCE GUIDE For additional technical information contact Fastenal Engineering at engineer The torque values can only be achieved if nut or tapped hole has a proof load greater than or equal to the bolt s minimum tensile strength 2 For A307A J429 Grade 5 and 8 H K Grade 9 EcoGuard A574 A193 B7
Detailed torque specifications for the Chevy Silverado 1 made from 1998 2006 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs Fuel tank filler housing to Fuel tank fill pipe bolts 2 1 Model 1500; Engine; 2WD; Fuel system Fuel tank filler
% %âãÏÓ 10332 0 obj > endobj 10349 0 obj >/Encrypt 10333 0 R/Filter/FlateDecode/ID[3983CA46861FB94C964F811D4CA2747F>7F956545A493AD42B3129AA916D4AA16
Detailed torque specifications for the Ford F150 12 made from 2009 2014 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs Oil pan bolts 20 15 Bolts 1 9 and 11 14 Stage 1 Engine; Oil pan Oil pan bolts 10 7 Bolts 15 and 16 Stage 2
Detailed torque specifications for the Ford F150 10 made from 1997 2004 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs
5 Tightening Patterns Tightening bolts in the proper sequence is critical Star Patterns Tighten bolts in a crisscross star pattern to evenly load the joint Apply torque in increments of 30% 60% 100% Spiral Patterns Sequence tightening in a spiral pattern from the center out This also evenly loads the joint
This calculator uses a practical starting point for all threaded fastener tightening analysis and uses the basic elastic torque tension equation This fastener bolt torque calculator will Estimate the unknown torque diameter axial force applied and coefficient of turning friction for
Detailed torque specifications for the Volkswagen Golf VII Mk7 made from 2012 2017 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs Twelve point bolt without ribs CVs Outer CV joint bolt 70 52 Mounted CV joint VL107 Twelve point bolt with ribs
The Bolt Torque & Preload calculator can be used to calculate the torque required to achieve the desired preload on a bolted joint See the reference section for details on the methodology and the equations used Bolt Properties Bolt Material Create New New Thread Size Inch
Detailed torque specifications for the Chevrolet Cruze 1 made from 2008 2016 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs Torque converter to Flywheel bolt 60 44 6T30 Automatic Transmission; Torque converter Torque converter to Flywheel bolt
Detailed torque specifications for the Dodge Ram 2 made from 1994 2002 and tightening torques for all of its components including the wheels engine brakes suspension and exhaust in both Nm and ft/lbs
TORQUE TENSION REFERENCE GUIDE For additional technical information contact Fastenal Engineering at engineer The torque values can only be achieved if nut or tapped hole has a proof load greater than or equal to the bolt s minimum tensile strength 2 For A307A J429 Grade 5 and 8 H K Grade 9 EcoGuard A574 A193 B7
Auger Torque was established in Europe in 1998 creating a new standard in the earth moving attachment market ISO 9001 accredited and awarded with two Queens Awards Auger Torque is recognised for its quality and innovative products
Auger Torque was established in Europe in 1998 creating a new standard in the earth moving attachment market ISO 9001 accredited and awarded with two Queens Awards Auger Torque is recognised for its quality and innovative products
When working on your vehicle s Ecotec engine getting the torque specs right is crucial for a successful repair or performance upgrade Here s a comprehensive guide to help you navigate the torque specifications for various components of this engine Why Torque Specs Matter Torque specifications are essential because they ensure that bolts and nuts are
The rear cab mount bolts torque specification is 20 lb /ft which is the same for the radiator support mounts Jim 1965 Impala SS 400 sbc Muncie rock crusher 1966 Impala SS 396 bbc TH 400 1969 El Camino 350 sbc TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed stepside TH 400 427 BBC 03 17 2009 11 53 AM
Table V Bolt Torque [No lubrication on threads Torque values are based on friction coefficients of between threads and between nut and washer or head and washer as manufactured no special cleaning ] Size Root area in 2 Torque range class 8 150 ksi bolts Note 1 10 24 23 to 34 in lb 10 32
© Copyright 2024 By Ore Crushing Equipment Manufacturer
